Ubiprog 5000 programmer is High performance Universal eprom
Programmer. Universal ubiprog 5000 programmer is the replacement of
SUPERPRO 611S programmer, Ubiprog5000 flash programmer designed for
supporting Flash memories, Nand flashes, Serial EEPROMS,
Microcontrollers & Automotive ECU, Dashboard parts.
Universal ubiprog 5000 programmer will replace SUPERPRO 611S
Ubiprog 5000 EEPROM Flash Programmer (48Pin socket)
UBIProg 5000 Programmer is very fast, Low cost, High performance
Universal Programmer, specially designed for supporting Flash
memories, Nand flashes, Serial EEPROMS, Microcontrollers &
Automotive ECU, Dashboard parts. The Heart of UBIProg 5000 is a
500.0000 Gate FPGA with a designed CPU core with 96MHz Clock for
fast programming of chips.
Ubiprog 5000 programmer Features:
21000 Supported Devices Flash Memory (Parallel / Nand /Serial) ,
EPROM , EEPROM , Serial EEPROM , Microcontroller , NVRAM , FRAM ,
CPLD , PLD , FPGA).
48-Pins ZIF Socket with Pin Continuity tester & 10-Pins
USB 2.0 High Speed ,Program 1 Gbit Nand Flash less than 50 sec ,
Reading Serial Flash memory with 6 Mbit/Sec Speed.
Auto detection of all flash Memories/Microcontrollers with Device
User friendly software for WIndows XP/VISTA/7 (32,64 bits).
Multiple Programming is possible by attaching 2 or more Programmers
to one PC.
Very low cost Main Unit & Low cost adaptors by using one
adaptor for all 32/40/48 TSOP flash memories . All 56 pins flash
memories by one TSOP56 adaptor.
Special Abilities like, ALtera U S B B l a s t e r Emulation for
Quartus Software, Serial Port Emulation , Vehicle ECU , Immoblizer
& Dashboard microcontroller Support.
Parallel Flash Memories: up to 56 pins parallel flash memories are
supported by UBIProg5000. it Supports different kind of packages
(PLCC , TSOP1 , TSOP2 ,VSOP & ...). All Flashes can be
automatically detected by software in case of unreadable device
names. By using a single adaptor for all 32-48 pins TSOP flashes ,
user only need 1 adaptor for over 1000 flash chips.
Nand Flash Memories: UBIProg 5000 has an additional Nand+ software
, specially designed for Nand flash memories. Nand+ Software has
one of the most complete list of Nand flash Memories with
algorithms for correction of bad data in MLC Nand Flashes.
UBIProg5000 is one of the fastest Nand Programmers in the world
with Read & Write Speed up to 8 MegaByte per Second. All Nand
Flashes can be automatically detected by software in case of
unreadable or remarked device names.
Serial Flash Memories: All 8-16 Pins Serial SPI flash memories are
supported by UBIProg5000. All SPI flash Memories can be detected
automatically by software in case of unreadable device names. It
reads & programs SPi flashes with maximum safe speed on ZIF
(6-7 Mbit/second) . Also it Unprotects the write protected flashes
before writing data to it.
ATMEL: All AVR 8 bits chips (ATMEGA/ATTINY/AT90S) are supported on
ZIF Scocket & by ISP cable. High Voltage Parallel on ZIF
Programming of AVR up to 64 pins is supported. newly introduced
ATXMEGA Series are supported by both PDI & JTAG Method. Old C51
series & new single cycle C51 series are completely supported.
All the above series can be detected automatically by UBIProg5000.
ARM7 programming by JTAG is supported.
Microchip: One of the most complete device list for microchip PIC
microcontrollers including all PIC12F /PIC12C /PIC16C / PIC16F /
PIC18F / DPIC33F / J & K Series. Devices up to 40 Pins can be
programmed on ZIF , All PICs can be detected automatically &
programmed by ISP cable.
Others: ST, SST, Philips (NXP) , Motorola , Syncmos, Silicon Lab ,
ICSI , , Intel , Winbond & ...
Automotive MCUs: Supporting of ST10F & TMS370 Series by ISP
cable for many BOSCH/VALEO/SAGEM ECUs (complete ST10F support of
XPROG-m programmer device list). supporting of siemense &
SAK-C167 connected to 44 or 48 pins flash (Siemense/BOSCH/SAGEM
S2000 ECU) like HSE FlasHit Programmer. Supporting NEC &
Motorola Devices for Dashboards.
PLD/CPLD/FPGA: Supporting All ALTERA JTAG Devices by emulation of
USB B l a s t e r Programmer in Quartus Software. Supporting of
Xilinx CPLD/FPGA with jed file. Fast Xilinx FPGA configuration with
bit file. Supporting of GAL/PALCE Devices with special option for
Software: With multiple language support (English / Chinese /
Arabic / French /FARSI). More languages & Devices can be added
by customer request. You Can Download Software & run it in Demo
mode to evaluate it.
Programmer adapters: We have a policy for minimum price for
adaptors, our adaptors can be used for many different packages. In
many cases we support other programmer manufacturers adaptors on
our device. Here are example of some of our adaptors:
For All 32/40/48 Pins TSOP Type-1 (20mm Pin-Pin Lenght) , You Need
Only one adaptor Model 548T2
ubiprog 5000 programmer adapters:
For All 56 Pins TSOP Type-1 (20mm Pin-Pin Lenght) , You Need Only
one adaptor Model 556T2 , with different sets of bottom plates
which can be easily exchanged by user.